Do It Yourself Bath Setup.
Do It Yourself Bath Setup.
Blog Article
We have found this post about A Step-by-Step Guide to Installing a Bathtub listed below on the internet and think it made good sense to share it with you over here.
Installing a bath tub isn't specifically brain surgery, yet it does require solid plumbing, carpentry, and often, tiling abilities. Changing an old bathtub with a brand-new one is also a moderately challenging job. If the old tub is easily easily accessible, the task can move easily; if you have to open a wall to remove the old bathtub and position the new tub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly require an assistant to leave the old tub as well as embeded in the brand-new one. See to it you have certified on your own for the work as well as are comfortable attempting it. Instead of employing a professional to take over a halfway-completed project, it is much better to think about utilizing one before you begin. Chances are you might need a professional plumber to make tube connections.
This write-up will certainly assist you mount a brand-new tub in your shower room if you have already bought a brand-new tub and also don't need to alter the arrangement of your previous water supply pipelines.
Your devices as well as material checklist ought to consist of the following:
Preparing for the Setup
To start with, the supporting frame provided with the bathroom must be fitted (if required) according to the supplier's instructions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to see to it that if the faucet features a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets unit to stop stress on the bathtub.
Fit the adaptable tap ports to the bottom of the two faucets utilizing 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom should currently prepare to be suited its last setting.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you ought to do is separate the supply of water. After doing so, switch on the taps to drain any water continuing to be in the system. The process of eliminating the existing taps can be fairly problematic due to the restricted accessibility that is typically the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the taps. Have a fabric all set for the continuing to be water that will originate from the pipelines. Once the supply pipes have actually been removed, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. When the faucets have been eliminated, the holes in the bath/basin will need to be cleansed of any old sealing compound.
Before proceeding to fit the new faucets, compare the pipeline links on the old taps to the new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new taps to fit.
Mounting the Bathtub
Using the two wood boards under its feet, position the bath tub in the called for position. The wooden boards are helpful in equally spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto four tiny factors.
The following goal is to make certain that the bath tub is leveled all round. This can be attained by checking the spirit level and changing the feet on the bathtub up until the spirit level checks out degree.
To mount taps, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression join; after that do the exact same for the various other tap.
Turn on the water and examine all joints and also new pipework for leaks as well as tighten them if needed. Fill the tub and likewise check the overflow outlet and the typical electrical outlet for leakages.
Lastly, deal with the bath paneling as described in the producer's instruction manual. Tiling as well as sealing around the tub ought to wait till the bath tub has actually been used at least once as this will certainly resolve it into its last setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly call for decreasing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin ensuring that the washing machines are in place in between the tap and also the sink. Secure the faucet in place with the supplier provided backnut. As soon as the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet adapters. The former type needs to be connected to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to crack a stiff seal, triggering the water to pass through the wall surface between the bathroom as well as the tiling, causing difficulties with moisture and also possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also fittings. They are offered in tubes and also cartridges, as well as can securing spaces as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched paper or soft rope. Keep in mind to constantly fill up the bath tub with water before sealing, to allow for the movement experienced when the tub remains in use. The sealant can crack relatively very early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is advisable to fit the tiles making use of water-resistant or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
I recently found that content on Installing A Bathtub when perusing the search engines. Sharing is good. Helping others is fun. I value reading our article about Installing A Bathtub.
Additional Resources Report this page